maintenancecenter, writer
115
edits
Difference between revisions of "ORBIGate Manual User's guide"
Jump to navigation
Jump to search
m
no edit summary
m |
m |
||
| Line 62: | Line 62: | ||
The test is ready to be run. Clicking on the monitoring icon | The test is ready to be run. Clicking on the monitoring icon | ||
[[Image:ORBIGate_18.gif|framed|none]] | [[Image:ORBIGate_18.gif|framed|none]] | ||
as shown on the window below, will display the results. | |||
[[Image:ORBIGate_19.jpg|framed|none]] | [[Image:ORBIGate_19.jpg|framed|none]] | ||
| Line 609: | Line 609: | ||
====Alarm operation==== | ====Alarm operation==== | ||
When using the alarm, one needs to start the monitoring | When using the alarm, one needs to start the monitoring | ||
[[Image:ORBIGate_75.png|framed|none]] | [[Image:ORBIGate_75.png|framed|none]] | ||
in order to start monitoring data and check conditions. From that point, the conditions are checked and actions started. Here is below an example of data record started on alarms and data record pause when the level goes down. | |||
[[Image:ORBIGate_76.png|framed|none]] | [[Image:ORBIGate_76.png|framed|none]] | ||
| Line 863: | Line 863: | ||
|} | |} | ||
In the grid, Async results are noted with the initials AS after the result name | In the grid, Async results are noted with the initials AS after the result name. | ||
====The orbit==== | ====The orbit==== | ||
| Line 1,037: | Line 1,037: | ||
''Post Analysis signal selection'' | ''Post Analysis signal selection'' | ||
Once the signal is loaded, it will appear as in the window below | Once the signal is loaded, it will appear as in the window below: | ||
[[Image:ORBIGate_127.jpg|framed|none]] | [[Image:ORBIGate_127.jpg|framed|none]] | ||
| Line 1,162: | Line 1,162: | ||
|} | |} | ||
It is also possible to sweep forward and backward the history using the keyboard arrows | It is also possible to sweep forward and backward the history using the keyboard arrows. | ||
Using the navigation cursor, all the data is updated in the graphic zone. | Using the navigation cursor, all the data is updated in the graphic zone. | ||
| Line 1,236: | Line 1,236: | ||
|} | |} | ||
The reference values can be accessed in two ways: In the test point<nowiki>’</nowiki>s configuration or through the toolbar icon | The reference values can be accessed in two ways: In the test point<nowiki>’</nowiki>s configuration or through the toolbar icon. | ||
{|border="2" cellspacing="0" cellpadding="4" width="100%" | {|border="2" cellspacing="0" cellpadding="4" width="100%" | ||
| Line 1,257: | Line 1,257: | ||
When accessing the "set gap reference" values through the toolbar icon. The values measured (shown in the grid) appear in the table when the button "new" is checked. If the button "current" is checked, the current values are shown. | When accessing the "set gap reference" values through the toolbar icon. The values measured (shown in the grid) appear in the table when the button "new" is checked. If the button "current" is checked, the current values are shown. | ||
At this stage, one should choose the corresponding position of the shaft and the preference for the 0 position (0 at center or 0 at bottom): Four choices are possible | At this stage, one should choose the corresponding position of the shaft and the preference for the 0 position (0 at center or 0 at bottom): Four choices are possible: | ||
{|border="2" cellspacing="0" cellpadding="4" width="77%" | {|border="2" cellspacing="0" cellpadding="4" width="77%" | ||