developer, maintenancecenter, writer
57
edits
Difference between revisions of "OR3X Hardware Instruments"
Jump to navigation
Jump to search
OR3X Hardware Instruments (view source)
Revision as of 10:48, 24 October 2023
, 10:48, 24 October 2023→Back panel connectors description
| Line 179: | Line 179: | ||
=====Back panel connectors description===== | =====Back panel connectors description===== | ||
* | * '''A''': Two Ethernet (1 Gb/s) connectors: One for connection to PC and one for cascade of analyzers. | ||
Connect the PC to IN. In cascade mode connect the PC to first analyzer (master) to IN. Next units are daisy chained (OUT -<nowiki>></nowiki> IN, OUT- <nowiki>></nowiki> IN, etc…) in cascaded mode. The cables required are Category 5 un-shielded twisted-pair. Use the blue cables. | |||
* '''B''': 2 clock synchronization connectors (100 Mb/s Ethernet). Please do not use while using a sole analyzer. Daisy chain from Master unit to the next one in cascaded mode (OUT -<nowiki>></nowiki> IN, OUT- <nowiki>></nowiki> IN, etc…). On the Mobi-Pack, synchronization connectors are on the front panel | |||
*'''C''': DC power in XLR connector (Not available on ORMP ). To be plug with the external power supply. Warning, do not mix the instrument power supply types. | |||
* 2 clock synchronization connectors (100 Mb/s Ethernet) | * '''D''': Mobi-disk. The Mobi-Disk holds the recorded raw data. So please power off the analyzer prior removing or inserting it. When using the analyzer without the Mobi-disk plugged in, use the obturator cover to protect the internal parts of the analyzer. | ||
* '''E''': Disk activity LED: The LED will flash while data are written on or read from the disk. | |||
* '''F''': USB 2.0 for raw data recording: To record on an external disk, power off the analyzer, remove the Mobi-Disk (put the obturator cover), plug your USB memory device and power on. The raw data will be saved on the memory device. Caution, the write speed on your memory device may lead to a throughput error, check the performance before using it for actual measurements | |||
* '''G''': Interface connector: RS-232 for remote control through RJ11 connector | |||
* DC power in XLR connector (Not available on ORMP ). To be plug with the external power supply. Warning, do not mix the instrument power supply types. | *'''H''': Reset. To be used when your analyzer does no respond to any command. Insert a paper clip in the hole and press smoothly. | ||
* Mobi-disk | * '''I''': Accessory Power supply. This connector provides power supply for external use (transducer, tachometer, etc… power supply). The available voltage and power are: | ||
1. <nowiki>+</nowiki>5V, 3W, 1.6 A | |||
* Disk activity LED: The LED will flash while data are written on or read from the disk. | * | ||
* USB 2.0 for raw data recording: To record on an external disk, power off the analyzer, remove the Mobi-Disk (put the obturator cover), plug your USB memory device and power on. The raw data will be saved on the memory device. Caution, the write speed on your memory device may lead to a throughput error, check the performance before using it for actual measurements | 2. <nowiki>+</nowiki>9V, 6W, 650 mA | ||
* Interface connector: RS-232 for remote control through RJ11 connector | * | ||
* Reset. To be used when your analyzer does no respond to any command. Insert a paper clip in the hole and press smoothly. | 3. <nowiki>+</nowiki>15V, 6W, 25 mA | ||
* Accessory Power supply. This connector provides power supply for external use (transducer, tachometer, etc… power supply). The available voltage and power are: | *'''J''': High speed port: Used for connection the CAN bus probe | ||
*'''H''': Ground connection. Use this screw to connect the analyzer to the ground potential | |||
* <nowiki>+</nowiki>9V, 6W, 650 mA | |||
* <nowiki>+</nowiki>15V, 6W, 25 mA | |||
* High speed port: Used for connection the CAN bus probe | |||
* Ground connection. Use this screw to connect the analyzer to the ground potential | |||
====DC Power supply==== | ====DC Power supply==== | ||