NVGate Ribbons: Home

From OROS Wiki
Jump to navigation Jump to search

Go to result group

Online mode

 

  Start...: Opens the NVGate start dialog which is dedicated to make the first steps in the software. The NVGate start dialog is also displayed at each NVGate Start except if the user checks the option Do not show again in the dialog.
  Open project: Opens the NVGate Start dialog which is dedicated to make the first steps in the software. The Start dialog is also displayed at each NVGate Start except if the user deactivates the option in the bottom left of the dialog.
  New project: Opens the NVGate Start dialog which is dedicated to make the first steps in the software. The Start dialog is also displayed at each NVGate Start except if the user deactivates the option in the bottom left of the dialog.


  Online to Post-analysis: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.
  Select inputs: Opens the Inputs selection dialog which allows activating and setting-up the dynamic inputs in a fast and smart way.
  Show results: Opens the Results dialog which allows displaying and saving results without connecting inputs or tracks to the plug-in analyzers in advance.
  Results overview: Opens the Results overview table which summarizes all the displayed and saved result (i.e. present in the Save Selection list)


Post-analysis mode

 

  Post-analysis to online: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.
  Select signal: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.
  Select tracks: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.


Measurement group

 

Note that another Run/Pause/Stop button is always available in the status bar (bottom left)

  Run: (CTRL+R) This button controls the general analysis and recording start. The plug-ins with connected channels/tracks will start their process once the run is activated.

Note: The monitor and the Time Domain Analysis (in free run mode) process is continuous; it do not depends on the run status.
Note: the trigger/start status of the plug-ins may block their process, waiting for an event.""
Warning: Pressing the run button during an analysis leads to reset all current analyses, restarting all averages from 0. The analyzed data will be lost.

  Pause: Suspend or un-suspend the current analysis.

Note: If the recorder is running, it starts / finishes a record.

  Stop: (CTRL+S) Stops all the current analyses and recording. After requesting a stop, the plug-ins finish their current block. When all the plug-ins have switched to Stop the analyzer switches to the Stopped status

Note: The analyzed results and recorded signal are saved when the analyzer switch to stop. This is the default behavior. It may be changed from the user preferences.


Save group

 

  Save measurement: Save the result of the last measurement. This button is available when:
  • There is at least one result selected in the save selection,
  • The measurement is stopped,
  • The result exists.
  Save option: Defines the way the results and signals are saved. It opens the Save setup dialog which contains 2 tabs.


Setup group

 

Load setup: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.
Save as model: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.
Active model: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.
Reset: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.


Data group

Attachment: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.
  Filter projects: Enables to copy or move Projects / Measurements / Models from a specified source to the current Projects database.


Disk group

 


Record: Enter the preferences setting at the 1st tab. It allows customizing the scales font size, the refreshing speed as well as default specialized modes.
Used space: Gives a visual overview of the disk occupation.
Download: Enter the preferences setting at the 1st tab. It allows customizing the scales font size, the refreshing speed as well as default specialized modes.


User