NVGate Ribbons: Home

From OROS Wiki
Jump to navigation Jump to search

Go to result group

Online mode

Home gotoresult 2022.PNG

Home start 2022.PNG Start...: Opens the NVGate start dialog which is dedicated to make the first steps in the software. The NVGate start dialog is also displayed at each NVGate Start except if the user checks the option Do not show again in the dialog.
Home start 2022.PNG Open project: Opens the NVGate Start dialog which is dedicated to make the first steps in the software. The Start dialog is also displayed at each NVGate Start except if the user deactivates the option in the bottom left of the dialog.
Home start 2022.PNG New project: Opens the NVGate Start dialog which is dedicated to make the first steps in the software. The Start dialog is also displayed at each NVGate Start except if the user deactivates the option in the bottom left of the dialog.


Home online to PA.PNG Online to Post-analysis: This button is used to switch from Online mode to Post-analysis mode. This will open the Select Signal window which lists all the recorded signals available. The selected signal will be then playback and can be re-injected into any plug-in analyzer (Monitor, FFT, 1/n Octave...). It is also possible to play back a recorded signal through the Output during Online analysis.

See player page for more details.

Home select inputs 2022.PNG Select inputs: Opens the Inputs selection dialog which allows activating and setting-up the dynamic inputs in a fast and smart way.
Home show result 2022.PNG Show results: Opens the Results dialog which allows displaying and saving results without connecting inputs or tracks to the plug-in analyzers in advance.
Home results overview 2022.PNG Results overview: Opens the Results overview table which summarizes all the displayed and saved result (i.e. present in the Save Selection list)


Post-analysis mode

Gotoresult PA 2022.PNG

Home PA to online 2022.PNG Post-analysis to online: This button is used to switch from Online mode to Post-analysis mode.
Home select signals 2022.PNG Select signal: Opens the Select signal dialog to select the signal to be post-analyzed.
Home select tracks 2022.PNG Select tracks: Opens the Inputs table showing the inputs definition of the signal to be post-analyzed.


Measurement group

Home measurement 2022.PNG

Note that another Run/Pause/Stop button is always available in the status bar (bottom left)

Home run 2022.PNG Run: (CTRL+R) This button controls the general analysis and recording start. The plug-ins with connected channels/tracks will start their process once the run is activated.

Note: The monitor and the Time Domain Analysis (in free run mode) process is continuous; it do not depends on the run status.
Note: the trigger/start status of the plug-ins may block their process, waiting for an event.""
Warning: Pressing the run button during an analysis leads to reset all current analyses, restarting all averages from 0. The analyzed data will be lost.

Home pause 2022.PNG Pause: Suspend or un-suspend the current analysis.

Note: If the recorder is running, it starts / finishes a record.

Home stop 2022.PNG Stop: (CTRL+S) Stops all the current analyses and recording. After requesting a stop, the plug-ins finish their current block. When all the plug-ins have switched to Stop the analyzer switches to the Stopped status

Note: The analyzed results and recorded signal are saved when the analyzer switch to stop. This is the default behavior. It may be changed from the user preferences.


Save group

Home save 2022.PNG

Home save measurement 2022.PNG Save measurement: Save the result of the last measurement. This button is available when:
  • There is at least one result selected in the save selection,
  • The measurement is stopped,
  • The result exists.
Home save option 2022.PNG Save option: Defines the way the results and signals are saved. It opens the Save setup dialog which contains 2 tabs.


Setup group

Home setup 2022.PNG

Home load setup 2022.PNG
Load setup: Opens the Load setup dialog, which allows loading setups from Models, Measurements and Projects or creating setups for online or post-analysis.
Home save as model 2022.PNG
Save as model: Enables to save the current setup as a Model.
Home active model 2022.PNG
Active model: Displays the name of the loaded Model. This Model will remain active until a Reset setup is applied or another setup is loaded.
Home reset 2022.PNG
Reset: Closes the active Model and set all parameters to the default values.


Data group

Home data group 2022.PNG


Home attachment 2022.PNG Attachment: Enables to quickly identify if files (reports, pictures, videos....) are attached to the current project. Note: if the "Default project" is active, the Attachment button is greyed.
Home attachment 2022.PNG The Attachment folder of the current project is empty or does not exist.
Home attachment file 2022.PNG File(s) are located in the Attachment folder of the current project.

Home filter projects 2022.PNG Filter projects: Opens the Filter Project dialog, which enables selecting the projects to be visible in the Project manager.


Disk group

Home Disk group 2022.PNG


Home record 2022.PNG
Record: Enter the preferences setting at the 1st tab. It allows customizing the scales font size, the refreshing speed as well as default specialized modes.
Used space 2022.PNG
Used space: Gives a visual overview of the disk occupation.
Download 2022.PNG
Download: Enter the preferences setting at the 1st tab. It allows customizing the scales font size, the refreshing speed as well as default specialized modes.


User

User 2022.PNG