Lmagimel at 09:15, 26 November 2024

2024-11-26T09:15:38Z

← Older revision		Revision as of 11:15, 26 November 2024
Line 1:		Line 1:
	[[category:Modal]]		[[category:Modal]]
			[[category:WikiOros]]
	==Data acquisition==		==Data acquisition==

Lmagimel: /* Acquisition control */

2021-07-05T08:48:05Z

Acquisition control

← Older revision		Revision as of 10:48, 5 July 2021
Line 81:		Line 81:
	[[Image:Modal_Manual_110.png\|framed\|none]]		[[Image:Modal_Manual_110.png\|framed\|none]]

			'''Health:''' if overload or double hit happens, then Health LED becomes red.
	Health: if overload or double hit happens, then Health LED becomes red.

	When the acquisition is completed, press the button of [[Image:Modal_Manual_111.png]] or [[Image:Modal_Manual_112.png]] to transfer the data to the Modal main interface and start the modal identification.		When the acquisition is completed, press the button of [[Image:Modal_Manual_111.png]] or [[Image:Modal_Manual_112.png]] to transfer the data to the Modal main interface and start the modal identification.

Lmagimel: /* Acquisition control */

2021-07-05T08:47:49Z

Acquisition control

← Older revision		Revision as of 10:47, 5 July 2021
Line 80:		Line 80:

	[[Image:Modal_Manual_110.png\|framed\|none]]		[[Image:Modal_Manual_110.png\|framed\|none]]


			Health: if overload or double hit happens, then Health LED becomes red.

	When the acquisition is completed, press the button of [[Image:Modal_Manual_111.png]] or [[Image:Modal_Manual_112.png]] to transfer the data to the Modal main interface and start the modal identification.		When the acquisition is completed, press the button of [[Image:Modal_Manual_111.png]] or [[Image:Modal_Manual_112.png]] to transfer the data to the Modal main interface and start the modal identification.

Admin at 08:53, 10 September 2020

2020-09-10T08:53:56Z

← Older revision		Revision as of 10:53, 10 September 2020
Line 1:		Line 1:
			[[category:Modal]]
	==Data acquisition==		==Data acquisition==

Lmagimel: Created page with " ==Data acquisition== Data acquisition is a critical step for modal analysis: without correct data, no exploitable results. Thanks to the direct acquisition implemented in Mo..."

2020-07-20T07:23:46Z

Created page with " ==Data acquisition== Data acquisition is a critical step for modal analysis: without correct data, no exploitable results. Thanks to the direct acquisition implemented in Mo..."

New page

==Data acquisition==

Data acquisition is a critical step for modal analysis: without correct data, no exploitable results. Thanks to the direct acquisition implemented in Modal, enjoy the Teamwork analyzers power and accuracy with a dedicated interface for structural acquisition. The interface works with the different excitation modes: impact hammer, shaker, operating excitation.

[[File:Modal_Manual_03.jpg|framed|none]]

To excite a large structure, up to 6 shakers per analyzers can receive signals from generators outputs. In order to fit the wide range of potential cases, the complete series of excitation signals from random, chirp, swept sine, stepped sine to normal modes can be generated.
[[File:plane.png|framed|none]]

For high channel count applications, Teamwork technology cascades several analyzers together to acquire simultaneously hundreds of channels. Teamwork instruments guarantee an efficient instrumentation thanks to the different possible configuration.

[[Image:Modal_Manual_06.jpg|framed|none]]

For example, this flexibility allows to highly reduce the cable length by distributing the instruments along the structure under test.

The direct data acquisition (DAQ) module is available in Modal, which enables you to complete a modal test easily and quickly.

Launch the DAQ by clicking the "Data Acquisition" item, shown as the following.

[[Image:Modal_Manual_93.png|framed|none]]

Then the geometry modeled in Modal will be transferred to DAQ automatically.

[[Image:Modal_Manual_94.png|framed|none]]

To perform a complete modal acquisition, follow the different steps described here.

===Test planning===
In the preparation panel, set the test planning.

[[Image:Modal_Manual_95.gif|framed|none]]

[[Image:Modal_Manual_96.png|framed|none]]

===Transducers definition===
Set the transducer list in the <nowiki>’</nowiki>Transducers<nowiki>’</nowiki> page of Preparation Pane. Note to select the correct transducer type and fill the correct sensitivity.

[[Image:Modal_Manual_97.png|framed|none]]

Check the different mesurements directly on the geometry

[[Image:Modal_Manual_98.gif|framed|none]]

The references are displayed in red and the roving DOFs in green.

===Measurement parameters setup===
* Parameters Panel-<nowiki>></nowiki>Channel: set range for each active channel; match them to the corresponding measurement DOFs and transducers.

[[Image:Modal_Manual_99.png|framed|none]]

* Parameters Panel-<nowiki>></nowiki>Measurement: set the frequency range, spectral lines, average number, and window type.

[[Image:Modal_Manual_100.png|framed|none]]

* Parameters Panel-<nowiki>></nowiki>Trigger

[[Image:Modal_Manual_101.png|framed|none]]

===Display ans save options===
Action Panel-<nowiki>></nowiki>Display and Save: set the data blocks you want to display and export. As the following graph, trigger block, FRF H1, and coherence will be displayed, trigger block and FRF H1 will be exported in the Binary UFF format. You can go to this data storage directory to check files by pressing button [[Image:Modal_Manual_102.png]].

[[Image:Modal_Manual_103.png|framed|none]]

===Analyzer connection===
Click the button on the toolbar showed as the following to lunch NVGate and connect to it. During this process, you may be asked to operate the wizard of NVGate. You should confirm that the NVGate has been launched successfully before pressing the <nowiki>’</nowiki>OK<nowiki>’</nowiki> button.

[[Image:Modal_Manual_104.png|framed|none]]

If necessary, you may need to set the environment parameters of DAQ by the menu of <nowiki>’</nowiki>Operation<nowiki>’</nowiki>-<nowiki>>’</nowiki>Environment setting<nowiki>’</nowiki>. Please refer to the online help of DAQ for more details

[[Image:Modal_Manual_105.png|framed|none]]

Note that for acquisition with several synchronized analyzers, NVGate V10 minimum is required.

===Acquisition control===
Control Panel-<nowiki>></nowiki>Control: press [[Image:Modal_Manual_106.png]]to begin the measurement, [[Image:Modal_Manual_107.png]]to pause, and
[[Image:Modal_Manual_108.png]]to stop. If the <nowiki>’</nowiki>Auto Run<nowiki>’</nowiki> option is checked, the measurement sets will be executed automatically one by one, you don<nowiki>’</nowiki>t need to press the button [[Image:Modal_Manual_109.png]]
after one measurement set is finished. <nowiki>’</nowiki>Normal<nowiki>’</nowiki>, <nowiki>’</nowiki>Manual Accept<nowiki>’</nowiki> and <nowiki>’</nowiki>Overload Rejection<nowiki>’</nowiki> are different modes to accept the triggered data. You can also set <nowiki>’</nowiki>Double Hit Rejection<nowiki>’</nowiki> to reject the continuous hits when performing a hammer impact test to get better measurement quality.

[[Image:Modal_Manual_110.png|framed|none]]

When the acquisition is completed, press the button of [[Image:Modal_Manual_111.png]] or [[Image:Modal_Manual_112.png]] to transfer the data to the Modal main interface and start the modal identification.

Modal Data Acquisition - Revision history

Lmagimel at 09:15, 26 November 2024

Lmagimel: /* Acquisition control */

Lmagimel: /* Acquisition control */

Admin at 08:53, 10 September 2020

Lmagimel: Created page with " ==Data acquisition== Data acquisition is a critical step for modal analysis: without correct data, no exploitable results. Thanks to the direct acquisition implemented in Mo..."